#1 2010-02-04 01:49:26
[Lly] ASUS RT-N16 alpha?
千呼萬喚始出來的Oleg系列韌體，有興趣的可以前往下載。
其實界面還是和原來Oleg系列完全一樣，有點LKK 
版本確認：1.9.2.7-rtn-r1143
Wireless設定
連線數設定上限可到16384，比DD-WRT、Tomato有誠意一點 
新增WiMAX設定?
lly 提到:
It is alpha version and it has serious limitations:
1) WiFi will not up out-of-the-box (manual only)
2) printer+webcam+etc. not supported
3) bugs
To be fixed, but it will take some time.
下載網址：https://code.google.com/p/wl500g/downloads/list
技術問題請於論壇上集眾人之力公開討論，感恩
離線
#2 2010-02-04 01:55:37
Re: [Lly] ASUS RT-N16 alpha?
[root@rt-n16 root]$ dmesg
Linux version 2.6.22.19 (root@localhost) (gcc version 4.2.4) #2 Wed Feb 3 11:46:50 YEKT 2010
CPU revision is: 00019740
Determined physical RAM map:
memory: 07fff000 @ 00000000 (usable)
On node 0 totalpages: 32767
Normal zone: 255 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 32512 pages, LIFO batch:7
Built 1 zonelists. Total pages: 32512
Kernel command line: root=/dev/mtdblock2 noinitrd init=/sbin/init console=ttyS0,115200
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 512 (order: 9, 2048 bytes)
CPU: BCM4716 rev 1 at 480 MHz
Using 240.000 MHz high precision timer.
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 126036k/131068k available (2808k kernel code, 4880k reserved, 587k data, 124k init, 0k highmem)
Calibrating delay loop... 238.59 BogoMIPS (lpj=119296)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
PCI: Using membase 8000000
PCI: Initializing host
PCI: Reset RC
PCI: Fixing up bus 0
PCI: Fixing up bridge
PCI: Setting latency timer of device 0000:01:00.0 to 64
PCI: Fixing up bridge
PCI: Setting latency timer of device 0000:01:00.1 to 64
PCI: Enabling device 0000:01:00.1 (0004 -> 0006)
PCI: Fixing up bus 1
Time: MIPS clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
squashfs: version 3.4 (2008/08/26) Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
NTFS driver 2.1.28 [Flags: R/W].
io scheduler noop registered (default)
HDLC line discipline: version $Revision: 4.8 $, maxframe=4096
N_HDLC line discipline registered.
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at MMIO 0xb8000300 (irq = 8) is a 16550A
loop: module loaded
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V0.17
PPTP driver version 0.8.5-rc1
Physically mapped flash: Found 1 x16 devices at 0x0 in 8-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
Physically mapped flash: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Flash device: 0x2000000 at 0x1c000000
Physically mapped flash: squashfs filesystem found at block 1407
Creating 5 MTD partitions on "Physically mapped flash":
0x00000000-0x00040000 : "boot"
0x00040000-0x01fe0000 : "linux"
0x0015fffc-0x01fe0000 : "rootfs"
0x01fe0000-0x02000000 : "nvram"
0x00460000-0x01fe0000 : "flashfs"
Found a 0MB serial flash
sflash: found no supported devices
GACT probability NOT on
Mirror/redirect action on
netem: version 1.2
u32 classifier
Performance counters on
input device check on
Actions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1023 buckets, 8184 max)
ipt_time loading
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
Ebtables v2.0 registered
802.1Q VLAN Support v1.8 Ben Greear
All bugs added by David S. Miller
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 124k freed
Algorithmics/MIPS FPU Emulator v1.5
et: module license 'unspecified' taints kernel.
PCI: Setting latency timer of device 0000:00:02.0 to 64
eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.10.56.46
PCI: Setting latency timer of device 0000:00:01.0 to 64
eth1: Broadcom BCM4329 802.11 Wireless Controller 5.10.56.46
vlan1: add 33:33:00:00:00:01 mcast address to master interface
vlan1: add 01:00:5e:00:00:01 mcast address to master interface
vlan1: add 33:33:ff:31:43:3b mcast address to master interface
vlan1: dev_set_promiscuity(master, 1)
device eth0 entered promiscuous mode
device vlan1 entered promiscuous mode
device eth1 entered promiscuous mode
br0: port 2(eth1) entering learning state
br0: port 1(vlan1) entering learning state
br0: topology change detected, propagating
br0: port 2(eth1) entering forwarding state
br0: topology change detected, propagating
br0: port 1(vlan1) entering forwarding state
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
USB20H mdio control register : 0x80000018
PCI: Setting latency timer of device 0000:00:04.1 to 64
ehci_hcd 0000:00:04.1: EHCI Host Controller
ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:04.1: irq 5, io mem 0x18004000
ehci_hcd 0000:00:04.1: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
SCSI subsystem initialized
Initializing USB Mass Storage driver...
usb 1-2: new high speed USB device using ehci_hcd and address 3
usb 1-2: configuration #1 chosen from 1 choice
scsi0 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
scsi 0:0:0:0: Direct-Access FUJITSU MHV2060AH PQ: 0 ANSI: 0
sd 0:0:0:0: [sda] 116824680 512-byte hardware sectors (59814 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] 116824680 512-byte hardware sectors (59814 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00
sd 0:0:0:0: [sda] Assuming drive cache: write through
sda: sda1 sda2
sd 0:0:0:0: [sda] Attached SCSI disk
usb-storage: device scan complete
vlan1: no IPv6 routers present
br0: no IPv6 routers present
eth0: no IPv6 routers present
eth1: no IPv6 routers present
EXT3-fs: starting recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: mounting unchecked fs, running e2fsck is recommended
EXT3 FS on sda2, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
[root@rt-n16 root]$ 技術問題請於論壇上集眾人之力公開討論，感恩
離線
#5 2010-02-05 09:28:47
Re: [Lly] ASUS RT-N16 alpha?
hippo 提到:
另外, RT-N13U, DD-WRT
無動靜, Lly去年就有了. 有RT-N13U的網友或許可嘗試安裝Optware.
那個Lly版上的RT-N13U韌體，據了解並非Lly所開發的版本，應該屬於pptp官方加速版，其界面與功能就和原廠一樣(非LKK界面)。
http://wl500g.info/showpost.php?p=164400&postcount=3
技術問題請於論壇上集眾人之力公開討論，感恩
離線
#6 2010-02-07 16:16:43
Re: [Lly] ASUS RT-N16 alpha?
RT-N16刷了此版本後
參考
WL-500g 系列改機基本步驟
https://digiland.tw/viewtopic.php?id=158
reboot後發現
/usr/local/sbin/post-boot
不會自動啟動
可是手動下./usr/local/sbin/post-boot則可以啟動
哈~我是新手~爬了不少文都沒找到類似的解法~
不知各位有無碰過類似情況~請各位大大協助~
謝謝啦~~
最後修改： WQQ (2010-02-07 16:21:00)
離線
#7 2010-02-07 23:36:52
Re: [Lly] ASUS RT-N16 alpha?
我自己測過，沒遇過這個問題..
#!/bin/sh
sleep 2
# Activate swap
swapon /dev/sda2
# wait for /opt to mount
mount /dev/sda1 /opt
i=0
while [ $i -le 30 ]
do
if [ -d /opt/etc ]
then
break
fi
sleep 1
i=`expr $i + 1`
done
# Run all active services - active means starts with S
/opt/etc/init.d/rc.unslung
改了兩個地方：
1.是磁碟路徑 /dev/sda1、/dev/sda2
2.dropbear 拿掉了，可以直接在網頁上設定啟用 ssh
技術問題請於論壇上集眾人之力公開討論，感恩
離線
#9 2010-02-13 00:58:10
Re: [Lly] ASUS RT-N16 alpha?
1.9.2.7-rtn-r1193 出爐..
http://code.google.com/p/wl500g/downloa … an=1&q=rtn
技術問題請於論壇上集眾人之力公開討論，感恩
離線
相關討論主題
| 主題 | 回覆 | 點閱 | 最後發表 |
|---|---|---|---|
|
ASUS RT-N66U刷Shibby 140 MultiWAN後設定為無線AP 作者 lcjh20516
|
0 | 2354 | 2022-08-26 12:56:28 作者 lcjh20516 |
|
|
159 | 383164 | 2022-08-14 06:06:27 作者 lcjh20516 |
|
|
21 | 83348 | 2022-08-14 05:54:54 作者 lcjh20516 |
|
置頂 |
132 | 372848 | 2022-06-07 10:13:50 作者 dennys |
|
|
45 | 139703 | 2022-05-06 14:32:17 作者 max7441 |
