#1 2010-03-17 20:58:57
jffs2為什麼沒有mount?
已經在Web上啟用jffs2了, 但還是沒有jffs2
root@RT-N16:~# df -h
Filesystem Size Used Available Use% Mounted on
/dev/root 5.6M 5.6M 0 100% /root@RT-N16:~# nvram show |grep jffs
jffs_mounted=0
enable_jffs2=1
sys_enable_jffs2=1
clean_jffs2=0
dhcpd_usejffs=0
size: 24733 bytes (8035 left)
小弟是剛開始玩DD-WRT, 還請各位多多指教
humm... 怎麼不能把上傳的圖片插入到文章裡面 
補上我的dmesg, 我有接上一個USB-HDD, partition比較多阿哈哈
root@RT-N16:~# dmesg
Linux version 2.6.24.111 (eko@dd-wrt) (gcc version 4.1.2) #352 Sat Jan 2 13:28:35 CET 2010
CPU revision is: 00019740
Determined physical RAM map:
memory: 07fff000 @ 00000000 (usable)
On node 0 totalpages: 32767
Normal zone: 255 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 32512 pages, LIFO batch:7
Movable zone: 0 pages used for memmap
Built 1 zonelists in Zone order. Total pages: 32512
Kernel command line: console=ttyS0,115200 root=1f02 rootfstype=squashfs noinitrd
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 512 (order: 9, 2048 bytes)
CPU: BCM4716 rev 1 at 480 MHz
Using 240.000 MHz high precision timer.
console [ttyS0] enabled
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 124700k/131068k available (3112k kernel code, 6228k reserved, 1479k data, 144k init, 0k highmem)
Calibrating delay loop... 239.20 BogoMIPS (lpj=1196032)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
Generic PHY: Registered new driver
PCI: Using membase 8000000
PCI: Initializing host
PCI: Reset RC
PCI: Fixing up bus 0
PCI: Fixing up bridge
PCI: Setting latency timer of device 0000:01:00.0 to 64
PCI: Fixing up bridge
PCI: Setting latency timer of device 0000:01:00.1 to 64
PCI: Enabling device 0000:01:00.1 (0004 -> 0006)
PCI: Fixing up bus 1
NET: Registered protocol family 2
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
RT-N16 GPIO Init
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
squashfs: version 3.0 (2006/03/15) Phillip Lougher
io scheduler noop registered
io scheduler deadline registered (default)
HDLC line discipline: version $Revision: 4.8 $, maxframe=4096
N_HDLC line discipline registered.
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 8) is a 16550A
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
MPPE/MPPC encryption/compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V1.0
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky
PCI: Setting latency timer of device 0000:00:02.0 to 64
bcm_robo_attach: Using external reset in gpio pin 11
bcm_robo_attach: devid read succesfully via mii: 0x3115
bcm_robo_attach: mii access to switch works
bcm_robo_attach: devid: 0x3115
VID 0 is set in nvram, Ignoring
eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.10.56.27
PCI: Setting latency timer of device 0000:00:01.0 to 64
Physically mapped flash: Found 1 x16 devices at 0x0 in 8-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
Physically mapped flash: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Flash device: 0x2000000 at 0x1c000000
bootloader size: 262144
Physically mapped flash: Filesystem type: squashfs, size=0x59d0f2
partition size = 5991424
Creating 5 MTD partitions on "Physically mapped flash":
0x00000000-0x00040000 : "cfe"
0x00040000-0x01fe0000 : "linux"
0x00189400-0x00740000 : "rootfs"
mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only
0x01fe0000-0x02000000 : "nvram"
0x00740000-0x01fe0000 : "ddwrt"
Found a 0MB serial flash
sflash: found no supported devices
Broadcom Watchdog Timer: 0.07 initialized.
u32 classifier
Actions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
ctnetlink v0.93: registering with nfnetlink.
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team
ClusterIP Version 0.8 loaded successfully
TCP bic registered
TCP cubic registered
TCP westwood registered
TCP highspeed registered
TCP hybla registered
TCP htcp registered
TCP vegas registered
TCP scalable registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Welcome to PF_RING 3.2.1
(C) 2004-06 L.Deri
NET: Registered protocol family 27
PF_RING: bucket length 128 bytes
PF_RING: ring slots 4096
PF_RING: sample rate 1 [1=no sampling]
PF_RING: capture TX No [RX only]
PF_RING: transparent mode Yes
PF_RING initialized correctly.
PF_RING: registered /proc/net/pf_ring/
802.1Q VLAN Support v1.8 Ben Greear
All bugs added by David S. Miller
decode 1f02
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 144k freed
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
USB20H mdio control register : 0x8000000c
PCI: Setting latency timer of device 0000:00:04.1 to 64
ehci_hcd 0000:00:04.1: EHCI Host Controller
ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:04.1: irq 5, io mem 0x18004000
ehci_hcd 0000:00:04.1: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
SCSI subsystem initialized
Initializing USB Mass Storage driver...
usb 1-2: new high speed USB device using ehci_hcd and address 2
usb 1-2: configuration #1 chosen from 1 choice
scsi0 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
br0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
Algorithmics/MIPS FPU Emulator v1.5
device vlan1 entered promiscuous mode
device eth0 entered promiscuous mode
device eth1 entered promiscuous mode
br0: port 2(eth1) entering learning state
br0: port 1(vlan1) entering learning state
scsi 0:0:0:0: Direct-Access WDC WD50 00BEVT-00ZAT0 PQ: 0 ANSI: 2
sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 38 00 00 00
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 38 00 00 00
sd 0:0:0:0: [sda] Assuming drive cache: write through
/dev/scsi/host0/bus0/target0/lun0:<6＞usb 1-2: USB disconnect, address 2
sd 0:0:0:0: [sda] Result: hostbyte=0x07 driverbyte=0x00
end_request: I/O error, dev sda, sector 0
Buffer I/O error on device sda, logical block 0
sd 0:0:0:0: [sda] Result: hostbyte=0x01 driverbyte=0x00
end_request: I/O error, dev sda, sector 0
Buffer I/O error on device sda, logical block 0
unable to read partition table
sd 0:0:0:0: [sda] Attached SCSI disk
usb-storage: device scan complete
device vlan2 entered promiscuous mode
br0: topology change detected, propagating
br0: port 2(eth1) entering forwarding state
br0: topology change detected, propagating
br0: port 1(vlan1) entering forwarding state
device vlan2 left promiscuous mode
etherip: Ethernet over IPv4 tunneling driver
IMQ starting with 2 devices...
IMQ driver loaded successfully.
Hooking IMQ before NAT on PREROUTING.
Hooking IMQ after NAT on POSTROUTING.
IMQ driver unloaded successfully.
IMQ starting with 2 devices...
IMQ driver loaded successfully.
Hooking IMQ before NAT on PREROUTING.
Hooking IMQ after NAT on POSTROUTING.
usb 1-2: new high speed USB device using ehci_hcd and address 3
usb 1-2: configuration #1 chosen from 1 choice
scsi1 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
scsi 1:0:0:0: Direct-Access WDC WD50 00BEVT-00ZAT0 PQ: 0 ANSI: 2
sd 1:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: 38 00 00 00
sd 1:0:0:0: [sda] Assuming drive cache: write through
sd 1:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: 38 00 00 00
sd 1:0:0:0: [sda] Assuming drive cache: write through
/dev/scsi/host1/bus0/target0/lun0: p1 p2 < p5 p6 p7 p8 p9 p10 p11 p12 p13 >
sd 1:0:0:0: [sda] Attached SCSI disk
usb-storage: device scan complete
attempt to access beyond end of device
sda2: rw=0, want=4, limit=2
attempt to access beyond end of device
sda2: rw=0, want=4, limit=2
attempt to access beyond end of device
sda2: rw=0, want=4, limit=2
EXT3-fs: unable to read superblock 最後修改： kukat (2010-03-17 21:15:06)
附件:
2010-03-17_20.55.03.png, 大小: 76,821 bytes, 下載: 7離線
